Ultra DC Outputs

Ultra V-Series 400W
PSU Load 3.3V 5V 12V1 Wattage
All Rails
10% 1.34A 2.24A 1.95A 41W
20% 2.68A 4.47A 3.90A 73W
50% 6.71A 11.18A 9.76A 198W
80% 10.73A 17.89A 15.61A 308W
100% 13.42A 22.36A 19.51A 378W
110% 14.76A 24.60A 21.46A 411W





If our earlier comments seemed derogatory, you can now see the reason why. Obviously, this type of power supply will not withstand modern test methodologies. Every rail except the 12V rail falls far out of spec before we even reach 300W of load. This is the worst result we have seen so far, and we could see that there is no Under Voltage Protection installed since we measured just 2.6V on the 3.3V rail. You might be able to use this power supply in a budget system, but we would even hesitate to use it there.

Efficiency


Efficiency results are not the best either. Ultra achieves a maximum 75% efficiency, but with increasing loads it rapidly drops below 70%.

Ripple & Noise Results







Ultra V-Series 400W Ultra Performance - Continued
Comments Locked

37 Comments

View All Comments

  • zeroidea - Wednesday, November 7, 2007 - link

    The Antec PS featured in this article is currently on sale at staples.com for $30.

    http://www.staples.com/webapp/wcs/stores/servlet/S...">Link
  • SilthDraeth - Wednesday, November 7, 2007 - link

    I know it falls outside of the 450Watt max, but it is still below the 500 watt barrier. I just bought the psu for a midrange system I built my mom, I know it works well, but I don't have the ability to test everything.

    One can wish right?
  • Noya - Tuesday, November 6, 2007 - link

    If you look around (buy.com), the Corsair 450vx can be had from $51-61 pretty regularly, and at that price it's untouchable. I must say I've had one for about two months and haven't had any problems with it.
  • smthmlk - Tuesday, November 6, 2007 - link

    Can we have a full list of caps in each unit? Noting the primaries is nice, but what about the others? Thanks.
  • Talcite - Tuesday, November 6, 2007 - link

    Thanks for finally putting up O-scope readings, it's quite nice to see them. One thing I'm concerned about though is the lack of explication or analysis.

    For example, is the entire o-scope range 200mV in the 12v readings or is it one division? Also, there's a number of strange spikes in all the o-scope readings. I'm pretty familiar with the 450VX o-scope readings (mostly from other sites) and I haven't noticed any spikes of that nature in their readings. It probably isn't, but is the equipment faulty?

    Thanks for putting the readings up anyways though, they're a nice addition.
  • Super Nade - Tuesday, November 6, 2007 - link

    Those strange spikes are probe noise. If the probe is coupled incorrectly, you will see this artifact. This cold be due to any number of factors like EMI for instance. Following the ATX guideline on using 0.1 uF output coupling caps will minimize this to a great extent.
  • MrOblivious - Tuesday, November 6, 2007 - link

    You have to look at the sampling time on the readings to compare between sites. Different sampling times will make the traces appear a bit different.
  • phaxmohdem - Tuesday, November 6, 2007 - link

    I just recently built a rig for a buddy using a Thermaltake PurePower (or ToughPower.. can't remember) 480W Unit and it works like a champ powering a Core2 Quad Q6600 CPU, 2GB RAM, 2HDD's, two Optical Drives, 8600GT, TV Tuner and a few fans. (Wish I knew about the Corsair PSU when I spec'd that system out).

    But yeah, Unfortunately most people equate Watts to overall quality.... not unlike the MHz war of days gone by. Power supplies are one of the hardest components to convince people to spend extra on for some reason. FFS, electricity is kind of the basis of the whole dam computer!

    Eventually it ends up as "Oh well. Go ahead and get that 600W $30 power supply and let me know how that goes for ya. I could use a good laugh, and don't say I didn't warn you."
  • strikeback03 - Tuesday, November 6, 2007 - link

    Maybe Anandtech should go ahead and list the weight of each PSU. That has long been used as an estimate of quality.
  • jonnyGURU - Tuesday, November 6, 2007 - link

    Not any more. Topologies have changed to the point where you can have very light quality units and very heavy crap. Weight is NOT a factor.

Log in

Don't have an account? Sign up now